SE40520C

Moda

Moda LED Dimming Sensor Switch

SE40520C

Moda

Moda LED Dimming Sensor Switch

 Functions of the Moda:

Swipe
The lights are activated by a hand swipe across the sensor and deactivated the same way. In this mode, hold your hand in front of the sensor to dim the lights. The longer you hold the more the lights dim.

In Cabinet
The lights are activated by the opening of a door and deactivated once the door closes.

Recommended Location

RRP: £22.08
Description

 Functions of the Moda:

Swipe
The lights are activated by a hand swipe across the sensor and deactivated the same way. In this mode, hold your hand in front of the sensor to dim the lights. The longer you hold the more the lights dim.

In Cabinet
The lights are activated by the opening of a door and deactivated once the door closes.

Ordering options
Ordering options
 CodeDriverMax. WattageDetection RangeStockRRPQty
SE40520C
15/30W5cmIn Stock£22.08
 IDCodeDriverMax. WattageDetection RangeStockRRPQty
SE40520C
15/30W5cmIn Stock£22.08
CodeDescriptionStockColour CodingRRPQty
SE40525 15W LED Driver with 6 Port JB4 Distributor InStock
£22.68
SE40526 30W LED Driver with 12 Port JB4 Distributor InStock
£39.84
SE40548 Ultra Slim line 12V 30W driver InStock
£45.00
SE40553 6W Driver with 4 Port JB4 Distribution Block InStock
£17.40
SE40555 15W LED Driver with 6 Port JB4 Distributor InStock
£23.04
SE40556 30W LED Driver with 12 Port JB4 Distributor InStock
£37.68
SE40557.1 LED 24V 60W Driver with 12 port LED block InStock
£59.40
SE40599 30W Dimmable Driver InStock
£52.20
SE40625 6W LED Driver with 4 Port JB4 Distributor InStock
£16.68
CodeDescriptionStockColour CodingRRPQty
Product Features
Product Features
  • FinishAluminium

    Hint

  • Cable Length1.5 metres

    Hint

Key points:

> Activates and dims lights with motion.

Three functions:

> Mount inside a cabinet - open door to activate light.

> Mount under cabinet - swipe hand in detection range to activate light. Dimming function is available in this mode.

> 5cm detection range.

> Plug and play solution.

> Pre-set to monostable function.

> 1 x JB4 distribution block supplied with each sensor.

> 1.5m cable from sensor to distribution block.

> Works with any 12V or 24V product.

Product FAQs
Product FAQs

Does 'boxing in' the receiver affect the detection range of the remote control?

It depends on the material which the receiver is positioned behind. Wood for example does not affect the detection range, however metal will reduce the detection range to a degree. The detection range will also be affected if enclosed within a wall.

Does this product have a memory function?

Yes. When dimming your lighting using the SE40520, your settings will be remembered when you switch off your lighting. When you switch your lights back on, the last light level setting will be applied.

How many sensors can be used on one driver?

Sensors do not have their own wattage, therefore any amount of sensors can be used until they fill up the ports of the driver. The amount of lights that can be used on one driver is dependant upon the wattage of the lights and the wattage of the driver. To work out how many lights can be used on one driver divide the wattage of the driver by the wattage of the lights. A 24W (12V) driver used with the sensor will be maxed out one 24W has been used up.

Can you use 2 sensors on one light?

Yes.

Can sensors be used in the bathroom?

No. Our sensors are not IP rated so therefore they need to be installed outside the bathroom.

Can our products be used with those of other manufacturers?

We have not tested this so therefore do not recommend it.

Do I connect the "input" or "output" cable to the driver?

The "input" cable should be connected to the driver. The "output" cable should be connected to the light.

See more FAQs (5)
Downloads
Downloads
x

Selecting the right driver

Divide the wattage of the driver by the wattage of a single light to determine how many lights can be run by the driver.

For example, 15W driver with 3W lights
15 ÷ 3 = 5 lights

Drivers are available in more than one wattage, work out the best option based on the number of lights you have.

Drivers have a limited number of ports. A driver with 6 ports is therefore limited to a maximum of 6 lights.

Ensure you consider both the wattage and number of ports on the driver.

x

Connecting by Colour

To simplify the process of selecting the appropriate driver for your lighting, Sensio use a simple colour coding system.

All components are colour coded:

driver
close